How to Construct a 4-Strand Barbed Wire Fence Detail – When constructing a barbed wire fence, there are several basic steps that you can take to make it look great. You should know the proper placement of the braces and how to build a double-span braced corner.
In addition, you should also know how to create an angle brace, and use proper tension wire tension. Tension wire gives your fence strength and allows you to tighten it if it starts to sag.
Braced line post assembly
When installing a braced line post assembly for 4 strand bars in a boundary fence, it is important to follow certain rules of installation. The first step in the installation process is to drill a notch in a corner post.
The notch should be about two-thirds of the height of the fence. The most common mistake is setting the brace too high. In order to avoid this, cut the notch one-inch deep.
Before you begin installing the wire, determine the length and location of your fencing. Using a sketch, estimate the number of posts required to cover the area. Corner post assemblies are necessary when the fence changes direction and intermediate brace post assemblies are every 650 feet.
Generally, post distances should be 15 to 20 feet. You should space smaller posts closer together. You should also remember to place the wire on the side nearest the livestock when installing your fence.
In order to properly install the braced line post assembly, you must first measure the length of your fence. You can calculate this by dividing the height of the top wire from the ground by six inches.
You must also consider the depth of the ground where the posts will be set. For example, a fence that is 5 to eight feet deep will require a post with a top diameter of 8 inches.
A standard barbed wire fence usually uses three or four strands of wire. The spacing between the wires will depend on the animal species, as the wires are typically twisted together.
Using a braced line post assembly, each individual cable will sway slightly when animals come near the fence, discouraging them from fighting. This prevents the animal from trying to escape by escaping from the fence.
Double-span braced corner
To construct a double-span braced corner of a 4-strand barbed wire fence, begin by setting the corner post at least 2.5 meters (8.0 ft) deep in the ground. Use a piece of concrete or rock under the bottom of the brace post to prevent the corner post from sagging.
Then, secure a diagonal wire to the top of the brace post. Finally, make sure the tension wire is properly tightened. This is especially important for low spots and gullies.
To construct a double-span braced corner of a 4-strand barbed wire fence, begin by securing each post with a galvanized steel pin. Once the pin is secure, bend the wire back on itself and hook it through a staple.
Repeat this process for the other post. If the wire is not firmly attached to the corner post, it will slip under tension and may even tear or bend.
The double-span braced corner of a 4-strand barbed wire fence is a good example of a layered fence. This kind of fence is used to protect a perimeter area.
A thicker corner post will provide more support for the fence, so make sure you place a brace assembly every 650 feet. A braced corner is even more secure if the brace is supported by a concrete anchor.
Agricultural-style barbed wire is usually double-strand 12+1/2-gauge galvanized steel. It is woven between two fence posts, with gaps that get smaller towards the bottom.
In most cases, the wires are spaced 50 to 60 feet apart, with gaps between the wires smaller as they approach the bottom of the fence. The two types of barbed wire are typically used together, with the high-tensile wire positioned above the lower section.
When installing a double-span braced corner of a 4-strand barbed wire fence, make sure to use two identical line posts. This will prevent a coyote from digging underneath the fence.
The double-span braced corner is a good example of a wire fence that will last for many years. When choosing the best posts for the corners, make sure to consider the height and angle of the post.
Concertina barbed wire
A concertina barbed wire fence detail is an excellent way to deter trespassers. It is made from high-grade steel, and its spiral design allows for easy installation. The wire can be stretched or held in place with staples.
This wire is also galvanized, which means it is made from steel with a zinc coating. In addition, this wire is highly resistant to rust. Listed below are some of the benefits of concertina wire fencing.
This wire is attached to an adjoining roll or fence every four feet. It is advisable to hire a professional to install it because it requires special equipment and skills.
The installation of a concertina wire fence requires particular attention to the strength of the attachments, as well as the selection of brackets. After installation, the concertina wire should be stretched along the fencing line. This is the best way to protect property.
Zaun manufactures concertina barbed wire toppings and can provide custom options. The concertina wire toppings are typically used in places of critical national importance.
The razor-sharp blades on the concertina wire make it an effective deterrent for potential intruders. In addition, a concertina barbed wire fence can be made using stainless steel or galvanized steel.
In addition to concertina barbed wire fencing, this type of fence is also made with galvanized wire to avoid corrosion. Another benefit of this type of fence is its durability, which can last up to 40 years.
For example, if you have a property where you have an active pool, you can install concertina barbed wire fencing around the perimeter of the property. This fence detail is an ideal choice for a fence in a confined area.
These concertina barbed wires are available in several varieties. The BTO-22 blade is the most common. It has a 0.4mm thickness sheet and 2.2 wire diameter.
The BTO-22 Blade is also available in stainless steel and plastic-coated versions. The weight of the wire depends on how it is coiled. It weighs 0.3kg less than the single coil version. It is a better option if you need to use it for temporary fences in your yard.
Mesh wire fences
When choosing the type of barbed wire mesh to use, you have a few options. Choose polytope or poly wire, and consider the number of filaments, plastic weave quality, and locking system. If you choose poly tape, you will get a stronger fence and a higher visibility barrier for training and recognition.
The price of poly wire is cheaper but will last longer than poly tape. There are different capacities and locking systems to choose from, and you can buy a reel to move the fence if needed.
Another type of wire mesh is made of woven wire. These fences are often more expensive than woven wire, but they provide more protection for animals. They are also great for securing small crop acreages.
You can also use them for containing horses. High-tensile fences require less maintenance than mesh wire, and they can be constructed with wood posts or insulated metal. You can even add electricity to them for animal holding capabilities.
While installing a 4-strand barbed wire mesh fence, remember to make sure that it is properly supported. Metal posts will not hold up as well as wood posts. Make sure that wood posts are placed every 50 to 60 feet.
This will give more support to the fence and prevent it from sagging. If your fence is sagging, tighten the tension wire so it will hold up better. This way, you will not have to worry about the fence sagging.
While using a 4-strand barbed wire mesh fence is less expensive, you should consider its safety and effectiveness before purchasing one.
The sharp edge of the wire frightens away any intruders. A good 4 strand barbed wire mesh fence will last you for years. So, get it installed today! It is easy to install and will keep your livestock safe. You can even paint the barbs any color to add a pop of color to your fence.
Related: Chain Link Fence Slat Alternative
The cost of a 4-strand barbed wire mesh fence will depend on the material you choose. If you choose to use vinyl, you should estimate the cost of a 1,320-foot roll of the wire.
Besides the materials, the price of the project will depend on the size of your land. The larger the land area, the more material you need. And, of course, the more barbs, the higher the price will be.***
